- מותג: Audison
- דגם: AP5.9 bit
- גליון נתונים טכני: לחץ להורדה
- מדריך למשתמש: לחץ להורדה
Power Output
| Load. Imp. | 5 Channels |
| 4 Ohm | 20 W x 2 + 50 W x 2 + 150 W x 1 |
| 2 Ohm | 40 W x 2 + 90 W x 2 + 270 W x 1 |
Accessories
iDataLink Maestro AR interface – (Optional)
Keep your factory features and expand your level of in-vehicle connectivity with iDatalink Maestro AR. When your AP bit* amplifier is installed into a compatible vehicle using the iDatalink Maestro AR interface, you’ll be able to enjoy the OEM receiver controls (volume, tone, balance, fader, source selection) to manage the equivalent DSP function of AP bit amplifiers, making this process transparent for the user. This way, all the Head Unit factory functions including Steering Wheel Controls, Media Player (AUX-in and USB ports), Hands-Free Telephone, Voice Commands, Satellite Radio will be totally maintained.
* the optical input of the AP bit amps marked with a release version prior to R03 will be not usable when the amplifiers are connected with iDalink Maestro AR interface. R03 and R04 releases of all models will be fully compliant. You can check the release version on the bottom plate of the amp.
DRC – Digital Remote ControlThe DRC is the digital interface between the AP5.9 bit and the user. The DRC mounted in the vehicle dashboard, provides access to control of the inputs and volume adjustments, balance, fader and subwoofer volume. Providing source selection between main, aux and optical inputs, it also provides four of the configurations created and saved by the bit one right at hand. The DRC also controls the functions of the Audison Thesis amplifiers when these are installed in the same system.
ECK DRCDRC Cable Extension kit for installations on especially long vehicles. Total length of the supplied cable with the extension is equal to 6,5 m / 225,90".
OP 1.5 • TOSLINK Optical Cable Optical cable ending with TOSLINK connectors for S/PDIF digital audio signals. Cable length: 1,5 m / 59,05”.
OP 4.5 • TOSLINK Optical Cable Optical cable ending with TOSLINK connectors for S/PDIF digital audio signals. Cable length: 4,5 m/177,16”
STA • F/F Socket TOSLINK adapter Optical adapter to extend optical cables featuring TOSLINK connectors.
SPM4 – 4 Ch Stereo Passive Mixer
Recommended to extend the number of inputs of AP bit amplifiers because they feature a De-equalizer (De-Eq). In that case, any possible non-linear acoustic emissions due to the mixing of the pre-existing filtered channels are duly compensated.
APL 2 – (AP4 D / AP1 D) link cable
Cable to connect AP5.9 bit to AP4 D and AP1 D amplifiers.
AP T-Harness “DCC”.
AP Extension cables.
The Extension cable with Plug&Play connections allows total freedom in positioning the AP bit amplifiers.
AP Speakers Output cables.
The AP Speakers Output for AP5.9 bit is dedicated to the connection of the AP bit amplifiers with the input/output Extension cable.
DRC MP – Digital Remote Control Multimedia Play (OPTIONAL)
The new Audison DRC MP (Digital Remote Control Multimedia Play) is compatible with all the Audison electronics featuring AC Link bus. Its slim profile along with the holder supplied with it eases the installation in the best position inside the car. Thanks to the new Joystick, “Rubber Touch” finished for best control of the movements along the four direction axes, the 'DRC Settings' menu can be adjusted and navigation is also possible through the 'Navy Command' function if the system features an Audison bit Play HD with video output connected to a monitor.
- POWER SUPPLY :
Voltage: 7.5 ÷ 15 VDC
Idling current: 1.5 A
Switched off: <1.4 mA
Consumption @ 14.4 VDC 2Ω Max Musical Power (without CPL): 30 A
Remote IN 7 ÷ 15 VDC (1 mA)
Remote OUT 11 ÷ 15 VDC (200 mA)
Fuse 30 A
ART (Automatic Remote Turn on/off) Speakers to input – selectable
AST (Automatic Signal Turn on/off) Pre-In to input – selectable
CPL (Continuous Power Limiting) Max continuous power – selectable - AMPLIFIER STAGE :
Distortion – THD @ 1 kHz, 4 Ω, 90% Output Power (Ch 1-2-3-4): 0.08 %
Distortion – THD @ 1 kHz, 4 Ω, 90% Output Power (Ch 5): 0.1 %
Bandwidth (-3 dB, 2 V RMS, 4Ω): 10 ÷ 20k Hz / 10 ÷ 500Hz SUB
S/N ratio @ A weighted, 1V, Max Power: 95 dBA
Damping factor @ 1 kHz, 2 V RMS, 4Ω: >70
Input sensitivity: 2 ÷ 15 V RMS
Input impedance: 15k Ω
LOAD IMPEDANCE (MIN):
• Ch: 1-2-3-4-5 2Ω
MAX POWER 530 W
OUTPUT POWER (RMS) @ 12.0 ÷ 14.4 VDC, 1% THD:
• 5 Ch @ 4Ω: 20 W x 2 + 50 W x 2 + 150 W x 1
• 5 Ch @ 2Ω: 40 W x 2 + 90 W x 2 + 270 W x 1
OUTPUT POWER (RMS) @ 14.4 VDC, 10% THD:
• 5 Ch @ 4Ω: 25 W x 2 + 60 W x 2 + 190 W x 1
• 5 Ch @ 2Ω: 50 W x 2 + 115 W x 2 + 350 W x 1 - CEA SPECIFICATIONS :
Output power @ 4Ω, ⩽1% THD+N, 14.4 V: 20 W x 2 + 50 W x 2 + 150 W x 1
SN ratio (ref. 1 W output): 80 dBA - DIGITAL SIGNAL PROCESSOR (32 bit Cirrus Logic; Clock speed: 147 MHz) :
Crossover: Full / Hi Pass / Lo Pass / Band Pass
Crossover type and slope:
Linkwitz @ 12/24 dB – Butterworth @ 6/12/18/24 dB
Crossover Frequency: 68 steps @ 20 ÷ 20k Hz
Phase inversion: 0° / 180°
Analog Input Equalizer: Automatic De-Equalization
Output Equalizer
N.9 Parametrics Equalizers: ±12 dB; 10 pole; 20 ÷ 20k Hz
Time Alignment Distance 0 ÷ 510 cm / 0 ÷ 200.8 in.
Time Alignment Delay 0 ÷ 15 ms
Time Alignment Step 0,08 ms; 2,8 cm / 1.1 in.
Time Alignment Fine Set 0,02 ms; 0,7 cm / 0.27 in.
SYSTEM SET:
Preset (Drive Preset) Rotary switch for 7 installation Presets
Acoustic Preset N.2 DSP Memory, DRC selectable - CONTROL CONNECTIONS :
From / to personal computer 1 x micro USB-B
To Audison Electronics DRC controls
ASP For module: Automatic Speaker Presence
Optical / AUX select 12V control for Optical In / AUX enable
Master enable 12V control for Master In enable - GENERAL REQUIREMENTS :
PC connections Micro USB (1.1 / 2.0 / 3.0)
Software/PC requirements:
Microsoft Windows (32/64 bit): XP, Vista, Windows 7, Windows 8
Graphic card min. resolution: 800 x 600
Ambient operating temperature range: 0 °C to 55 °C (32°F to 131°F) - SIZE / WEIGHT :
Max size (mm/in.): 198 x 45,50 x 134 / 7.8 x 1.8 x 5.27
Weight (kg/lb): 1.5 / 3.3
